PortaPack H2 Desk Stand with Custom Callsign Plate

A desktop stand that keeps your PortaPack H2 upright, angled and ready to scan, with your callsign on the front plate.

Made to order in Quebec: printing starts within 1 to 3 business days and your stand ships in 3 to 5 business days, personalization included.

Most PortaPack owners end up propping the device against a coffee mug or laying it flat where the screen is unreadable. This angled cradle holds it at a comfortable viewing angle on your bench, with the knobs and buttons still easy to reach, so the radio lives on your desk instead of in a drawer.

A cable relief cutout at the back routes your antenna and USB cables cleanly behind the stand rather than out the front, and the wide base keeps the whole thing from sliding around while you tune. Drop the PortaPack in, hook up the antenna, and the station stays set up.

The customizable front plate is the centerpiece: your callsign, name, handle or short text of your choice, in a contrasting colour. It is how the SDR hobbyists, radio operators and security researchers I ship to make a bench setup feel like theirs.

🎯 Designed For

• PortaPack H2 combo owners who want a permanent desk station
• Ham radio operators wanting their callsign on display in the shack
• SDR hobbyists, RF enthusiasts and signal hunters
• Security researchers and Mayhem firmware users
• Gift buyers shopping for a radio or scanner hobbyist

✅ Features

✔ Device specific cradle shaped for the PortaPack H2 combo, so it sits secure rather than loose

✔ Angled screen position for clear reading and easy knob and button access while the radio stays on the desk

✔ Personalized front plate with your callsign, name or chosen short text

✔ Plate clips firmly to the base, so the two printed parts lock together into one solid stand instead of a loose piece that shifts

✔ Mix and match colours between the stand and the plate for a contrasting, two tone look

✔ Stable, compact footprint that will not creep across the bench while you work

📦 What's Included

• Desktop stand in your chosen colour
• Custom front plate in your chosen colour with your text
• Device not included

🛠️ Details

• Material: PLA, FDM printed at high infill for durability, with a matte finish
• Finished size: about 76 x 103 x 96 mm (3.0 x 4.1 x 3.8 in)
• Sized to cradle the PortaPack H2 with the antenna attached and pointing up
• Sits well beside a keyboard, next to a monitor stand or on a shelf at eye level, with a little clearance behind it so antenna and USB leads can pass through the rear cutout
• Front plate holds one short line of text, up to 12 characters, printed exactly as you type it, capitalization included
• Printed in the font shown in the listing photos unless you request another of the fonts pictured there
• Colour may vary slightly between filament batches, so a repeat order may not match an older piece exactly
• Made in Quebec, Canada by an active ham radio operator and 3D printing maker

🛒 How To Order

1. Pick your stand colour

2. Pick your front plate text colour

3. Type your callsign, name or chosen text in the personalization box, up to 12 characters so it fits the plate

4. Optional: message me with a font choice from the listing photos, your own logo file or any special request

5. Add to cart and check out

❓ FAQ

Q: I have a different SDR setup, will it fit? A: This one is cut for the PortaPack H2 combo only. Message me with your device and I likely have another version or can design one for you, including custom plate layouts.

Q: Will PLA hold up to daily bench use? A: Yes, printed at high infill it is stiff enough to hold the radio upright for everyday desk use. PLA does soften with heat though, so keep it off radiators, out of direct sun and out of a parked car.

Q: Can you put my club logo or my own artwork on the plate instead of text? A: Yes, send me your own logo or artwork file after ordering and I will fit it to the plate. I only print text and artwork supplied by you, not third party brand marks or logos.

Q: Are there customs or import fees for US buyers? A: No, I cover customs and import fees on US orders, so the checkout price is the final price. Buyers outside North America are responsible for their own country's duties.

⚠️ Please Note

Each stand and plate is made to order, so fine layer lines and slight texture are a normal characteristic of the printing process rather than a flaw. To clean, wipe with a damp cloth and avoid solvents. If anything arrives damaged or does not fit your device, message me with photos and I will replace or refund it.